How to Refill Windshield Washer Fluid to Your Car?

Windshield Washer fluid is important to clean the car front glass. It helps in providing a clearer view of the road ahead and prevents accidents. Know how to refill the washer fluid of the windshield.

How to Refill Windshield Washer Fluid to Your Car?
Filling Windshield Washer Fluid

Filling the windshield washer tank might seem a difficult task, but it isn't really one in most vehicles. When you press the lever to wipe the windshield, all you get is an empty wine bottle and the sound of the wipers scraping. All these signs indicate that you have to now top off your windshield washer fluid.

8 Steps on How to Refill Washer Fluid

1. Choose the best suited Windshield Washer Fluid

First things first, choose the best windshield washer fluid. Know that windshield washer fluid should not be made solely of water if you want it to do its job. Normal windshield washer fluid is formulated to work in a wide temperature range and not freeze in cold weather.

However, if you reside in a region that often suffers subzero weather, you should invest in anti-freezing washer fluid. On chilly mornings, when a thin layer of ice builds on your windshield, anti-freezing washer fluid can assist remove it. Moreover, additional compounds found in some windshield washer fluids cause rain to bounce away from the glass, improving visibility.

This is important because if wipers are used withour washer fluid, it may cause scratches which may lead to windshield repair or replacement. 

2. Mix concentrated fluid with water

As said in the previous point, the washer fluid should not be made of water only. You'll need to dilute concentrated windshield washer fluid with water before using it, provided you decide to go that route.

The concentrated windshield washer fluid can be diluted with water at a ratio of roughly 1:1, much as anti-freeze. There should be about as much liquid as there is water.

Also, don't forget to use only the concentrated washer fluid recommended for your vehicle's make and model.

3. Try to Find Where the Fluid Tank is Located

Typically a washer fluid tank is attached to the wall that runs down one side of the engine compartment, and it is frequently located along the firewall close to the windshield. The tank for the windshield washer fluid will be denoted with a sign that resembles a windshield with the wipers moving across it.

4. Find the Low and High Fill Lines of the Tank and Label them

Once you have found the tank, you must then locate the low and high fill lines that run alongside. The tanks for windshield washer fluid are typically composed of translucent plastic. Also, it includes markings down the side that display the amount of fluid in the tank.

NOTE: If the tank for the windshield washer fluid is full, but the sprayer does not work, then the problem may be caused by clogged pipes or may be due to the defective sensor. In such a situation, we recommend taking your vehicle to a professional windshield repair/replacement service provider.

5. Pour the Fluid into the Tank

After you have removed the screw cap, it's time to pour fluid into the tank. Add fluid into the tank with a funnel. Keep pouring until it is topped up to the "full" mark on the side of the tank.

Keep paper towels or a cloth handy. You can use them to clean up any spills that may have occurred when you pour the fluid. Make sure to keep watching the side of the tank so that you can determine whether or not it is full.

6. Don't overfill the tank

Make sure not to overfill the tank. It is because of the fact that overfilled tank fluids are likely to expand upon being heated. Also, excessive fluid in the tank increases the risk of a leak as the fluid expands when it heats from the high engine temperatures beneath the hood. In any case, if you still mistakenly overfill the tank, excess liquid can be removed with a turkey baster.

7. Turn on your Car to Check the Fluid

After following the steps above, sit back in your car and turn it on. To ensure that the windshield washer fluid is operating as it should, start the engine and activate it in the same way as you would usually. In the majority of the windshield washer fluid jets, you need to press or pull the controls for the windshield wipers.

If you seem not to get a hold of how to activate the windshield washer fluid, then you must refer to the instruction booklet or contact professionals.

8. Take the Hood off

Last but not least, take the hood off. The button to press to open the hood is usually located on the driver's side of the car, close to the door frame. A tiny icon depicting the front of a vehicle with the hood open is typically used to denote the release.

For the hood to drop, pull the release toward you to unlock it. When you get out of the automobile, don't forget to unlatch the safety latch. To deactivate the safety feature, press the lever located either under the hood or through the front grill. Seek advice from your car's handbook if you're unsure how to find the release.